ã€China Aluminum Network】 How to repair aluminum extrusion dies? Hunan Longfeng Aluminum Co., Ltd. gives you a brief introduction through the following articles: The main contents of aluminum profile extrusion die modification include: adjusting the proportion of metal flow distribution (such as: size adjustment of die diverter hole or diversion slot, depth adjustment of electric erosion drainage slot, etc.), adjustment of contact friction coefficient, and obstruction of interception. Such as: blocking the base, etc.) and adjusting the length of the working belt and other methods to change the speed of metal out of the mold hole, so that the metal evenly out of the mold hole, to produce qualified extrusion products. Therefore, the mold repair personnel must master the relevant inspection techniques to correctly analyze and judge the cause of product defects, and thus perform effective mold correction. The distribution ratio of metal supply is mainly determined by the mold designer and manufacturing. When the mold is manufactured, the proportion of metal is basically fixed. Designers must strive for a reasonable distribution. If the distribution is unreasonable, the flow velocity in the various parts of the profile will be uneven, which will cause difficulties in repairing the mold, and even if it is severe, it will not be possible to repair the mold. For most molds, although the amount of metal dispensed has been determined, the frictional resistance between the metal and the mold can be changed to achieve the purpose of adjusting the metal flow rate. The friction between the metal and the mold consists of three parts: the contact friction between the metal and the die surface, the contact friction between the die hole working belt, and the friction between the metal and the metal. Improve the metal and mold surface friction conditions, can play a role in adjusting the metal flow rate. Changing the amount of metal dispensed, the friction conditions, the length of the working belt, and the squeezing speed can all adjust the speed at which the metal flows out of the die hole. The mold modification mainly focuses on adjusting the metal distribution ratio, contact friction conditions, and the length of the die hole working belt to perform various effective methods to change the flow characteristics of the metal, so that the metal evenly flows out of the die hole and produces a qualified profile product. In order to overcome the defects caused by the uneven flow of metal, it is necessary to study how to make the metal flow rate at each section of the profile uniform. This is the principle that mold design should follow, and it is also the basic principle that molders follow. Although there are many factors that affect the speed at which metal flows out of the die hole, it can be summarized as two basic factors: a. Is it appropriate to distribute the flow of metal to all parts of the profile? That is, the ratio of the ratio of the cross-sectional area of ​​each section of the profile to the metal flow of the corresponding supply section is equal; b. When the metal flows, the magnitude of the frictional resistance is affected. When the amount of metal in a certain part of the supply profile increases, the frictional resistance is smaller, the faster the outflow speed of the die hole in this part of the profile, and vice versa. How to repair aluminum extrusion dies is summarized as follows: correct analysis and judgment, and reasonable adjustment of metal flow rate.
Zhongda Enterprise is now a leading steel
structure processing company in North-East China with full annual production
capacity of 40,000 T .Long span Steel Structure factory warehouse,
building Zhongda Enterprise was founded in 2002.and with in 15 years of
development, The company has grown to a multi-functional steel processing base,
with total ground area of 100,000㎡ and factory size of 68,000㎡. From 2009, according to the market demand, Zhongda entered into a new
field of long-span Steel Structure Bridge, and until 2016, Zhongda had
manufactured over 60,000 tons of steel structured constructions for government
projects, such as the Zone 2, Zone 3,Zone 4,overpass bridges, Benxi, Wuai
river-crossing bridges etc. Zhongda now has more than 400 employees and
more than 50 highly qualified employees with relevant certificates, and was
rewarded [Level One Nationalsteel ConstructionContracting Qualification "
. In order to respond the national strategy of [the Belt and Road
initiative", Zhongda Enterprise established a Liaoning Zhongda
Shenbang Industrial Co. LTD in China (Lioaning)free-trade district, with
specific purpose of developing prefabricated building and modular buildings,
with the initiation to maximize the advantage of Zhongda`s design and
manufacture ability. Great feedback were received from customers around the
world, including Europe, America, Australia, and Africa etc.
Zhongda Enterprise is now became a international steel structure construction
company, with multi-functions of designing, manufacturing, marketing, and
installation, with products including steel structured factories, shopping
malls, bridges, residential buildings, modular and prefabricated
buildings. Zhongda Enterprise, as a member of the Modern Construction Industry,
is willing to embrace the world and build a better home for everyone of us!
metal bridge Zhongda Steel Structure , http://www.zhongdametal.com
