Nowadays, many homeowners like to install aluminum windows with broken bridges during the renovation of their homes because of their good insulation, sound insulation, and heat preservation. However, after we use it for a period of time, we often feel that there is wind and wind, and it may be that the broken aluminum window leaks. Therefore, how to solve the leakage problem of broken aluminum windows ? Is there any good solution? The following let Xiaobian answer for you. How to do a broken bridge aluminum window leakage What to do if a broken aluminum window leaks ? Of course, you should first find out why. There are probably the following situations: 1. One of the most common causes is the aging and shrinkage of seals. Because the sealant strips are used for a long time, it is easy to cause aging and shrinkage by the wind and sun. Therefore, if this is the case, then it is advisable to replace the new seal. If you can't operate it yourself, you can find a professional worker, and the replacement cost will not be too much. 2. It is also possible that the glass glue is peeled off, aged and cracked. Although this situation is rare, it also exists. If yes, then you can find the original manufacturer to make a leak, or you can go to the building materials store to buy a bottle of glass glue. It is also possible to solve the problem by hand. It is very simple. 3. In addition, the leakage of aluminum windows that cause broken bridges may also be caused by the fact that the broken aluminum doors and windows are not closed properly. When installing aluminum doors and windows with broken bridges, leakage of air, leakage of water, etc. may occur when the technology is not in place. The solution is also very simple, find the factory debugging it. Solve the problem of window leakage 1, the old window window layout mezzanine For the double-layered, old-fashioned window, the best solution is to fill the sawdust between the window and the window, because it can solve the problem of moisture in the window, and it can also block the strongest cold air at the bottom of the window. Impenetrable. 2, plastic window plus plastic After the windows made of plastic material are used for a long time, it is very difficult to avoid airtightness, and even the gaps at some interfaces are too large to be bonded. However, we can paste it around the window with a sponge, and then cover the entire window with plastic, because it can absorb heat and ensure airtightness. It works well. 3, window gap processing If there is a gap between the window frame and the wall, the gap can be cleaned first, then filled with styrofoam, then filled with high-grade cement sand, and finally repaired with a Veneer; or with a sealing strip And felt strips, etc. are also possible. Xiao Bian concludes: The above is an introduction to the solution to the problem of air leakage in broken aluminum windows . I hope to help everyone. In fact, no matter if it is broken aluminum doors and windows or other materials of the doors and windows, once there is a problem, just find out the reasons, all problems will be solved.
Finger joint board, also known as integrated board, is a woodworking joint made by cutting a set of complementary wood pieces, to form long pieces of lumber from solid boards, the result is finger-jointed lumber. It is stronger then a butt joint or lap joint.
Luli Group Co., Ltd, is a professional manufacturer in wood panel products with rich experience. We are able to supply customers' requirements in panel products in various sizes and specifications with good quality.
The utility model of Finger Joint Board has the advantages because the connection of the solid wood joint is less, and the amount of rubber used is less, so it`s environment friendly.
It is easy to process, cutting and shaping.
The finger joint board can be very useful with fixing tables and chairs, also can be used high-end furniture making, wall panels, interior decoration and so on.
The details of Finger joint board:
Size: 1220mm x 2440mm(Standard size) or customize
Thickness: From 6mm to 30mm or according to request
Density: 480kg – 550kg/m3
Materials: Chile pine, Radiant pine, Mongolian scotch, White pine
Glue: E0, E1
Finger joint board Finger Joint Board,Wood Finger Joint Board,Finger Joint Lumber Board,Finger Joint Laminated Board Luli Group Co.,Ltd. , https://www.plywoods.nl
