First, adjust glue: 1. Take the appropriate amount of epoxy resin binding gum (G800) to the adjusting barrel, add the appropriate amount of dilution solvent; 2. Stir with a wooden stick to fully dissolve the black glue; 3. According to the black rubber viscosity after blending, adding vinyl or solvent, the viscosity of the judging to feel a little agitation in the prevail; 4. The well-prepared black glue is put into a glue bottle for use. Second, the sealing method: 1. Take a plate that measures the function and place it flat on the table; 2. The right hand holds the bottom of the Epoxy Bottle, and the tip of the Ejector tilts above the sealant; 3. With a little force, let the black glue flow out and drip on the IC. The black glue will flow and fill the seal area. 4. When the black plastic flows, the flow rapidly flows to the sealant range; when the other side has not flowed yet, the movable tip can be moved to the low glue position to add glue. 5. In the sealant, the height of the tip and the surface of the IC should not be lower than 1cm, and if it is too low, it may touch the surface or the state line of the IC; 6. Immediately after dropping an IC, raise the tip to prevent further dripping. Third, flow plastic trim: 1. Use a bamboo stick to wrap a small amount of cotton and tighten it with your fingers; 2. Gently remove the glue or glue; 3. Once failed to repair, replace the new cotton swab again; 4. When repairing the flow of sealant, pay attention to the action and fix the bad point. Do not reach the gold finger, so as not to touch the state line or IC. Fourth, the appearance of plastic seal inspection standards: 1. The board with a good sealant has a smooth and shiny surface, and the appearance is that the garden ball is slightly flat and strong, and the range is appropriate to cover all the golden fingers; 2. All the following phenomena are defective sealants: 1 glue has pores 2 less glue, obviously visible traces of state lines 3 exposed state line 4 glue 5 sealant exceeds allowable height 6 sealant exceeds allowable range 6 flow glue 8 vinyl cover element or via 9 surface is not smooth with water lines V. Storage and Drying Conditions of Vinyl: 1. According to requirements, black plastic should be stored in the environment below -5 °C, the shelf life is generally three months; 2. According to the current use of vinyl, the post-gel drying time is 2 hours and the temperature is 130°C. [Automatic Switch, Free Your Hands]: Cabinet light has two working modes, Motion & Light Sensor Mode, Always On and Off Mode. In G mode, this counter light automatically turns on when it senses human motion within 10 feet in a dark environment, and automatically turns off after 20 seconds of inactivity. You can use these lights as normal light or safe light. Solar Motion Light,Best Outdoor Motion Sensor Lights,Indoor Motion Sensor Light,Outdoor Sensor Lights Ningbo Wason Lighting Technology Co.,Ltd , https://www.wasonlights.com
[Upgraded Version & More Bright Sensor Closet Light]: With 20 LEDs(Not 10 LEDs) for each light, up to 160 lumens, more bright than other LED closet lights in the market, very easy to find what you're looking for and perfect to light up in a large space where there is no light system, like the cabinet, wardrobe, stairs, etc. HIBOITEC motion sensor light is the best choice for you.
[Larger Battery Capacity & Rechargeable]: Built-in 1000 mAh high-capacity rechargeable battery, has larger battery capacity than other led cabinet lighting, easily to charged via USB. After fully charged, these closet lights last for up to 8 hours under on mode and last 1-2 months under motion sensor mode. NEVER replace AAA batteries frequently. Energy Save & Save More Money!
[Two Ways to Install]: Easy to install and remove without any other tools. Using Magnetic Back Design, can stick on any ironwork, allows you to change the its location you need. Or you can use the included tape to attach the iron to any non-ferrous product surface. When you need to charge or change position, you can take down the closet lights at any time.