K11 waterproof paste is also called k11 high-grade waterproof material. This product is a two-component high molecular polymer modified base polymer waterproof system. There are unique and very active high-molecular polymer powders, synthetic rubbers, synthetic phenylene esters, etc. Emulsion blends, adding base materials and appropriate chemical additives and fillers, through plastication, mixing, rolling, etc. Processed polymer waterproof material, selection of imported materials and domestic high-quality accessories, in accordance with the highest level of national industry standards, the formation of quality products, listed as the Ministry of Construction to promote the key products. This article gives you a brief introduction of several k11 waterproof slurries and k11 waterproof slurries construction techniques. Let's take a look. First, nano net kitchen and kitchen waterproof slurry product description: 1. This product is a waterproof material for the kitchen and bathroom after many years of efforts and research and development by Meizhi Company. After many times of understanding and experimenting with the market and users, the product adopts nano materials and net odor technology. With formaldehyde, benzene, ammonia and other harmful substances. After repeated comparison tests: environmental protection and low carbon, easy construction, simple modulation, excellent leveling and waterproof performance. It is a special environmental protection waterproof slurry for home kitchen and bathroom decoration. It successfully solved the leakage problem of water seepage in kitchens and bathrooms caused by traditional waterproof materials. 2, the scope of application: kitchen, bathroom waterproof, can also be used as interior, exterior walls, basements, swimming pools, tunnels, slope roof and other buildings waterproof. Instructions: 1. Slowly pour the powder into the matching emulsion and mix it with an electric stirrer. Stir thoroughly for 3-5 minutes until a uniform mass of powder-free dough is formed. Let stand for 10 minutes to allow the slurry to fully mature and stir for 2 minutes. When stirring twice, the stirrer should be at the bottom of the container and not lifted so as not to trap air. The adjusted slurry should be used within one hour. 2. Brush the slurry evenly with a brown hair brush on a wet, but no clear water base surface, taking care to avoid leaking the brush. When the previous coating has cured and produces sufficient strength, the next layer is applied. The last waterproof layer is recommended to use a wool brush to make the surface smoother. If the surface is covered with a decorative layer, it is recommended that the last layer of waterproofing be applied with a brown brush for horizontal drawing to increase the degree of adhesion. Each brushing direction should cross each other vertically. 3. It is recommended to use glass fiber mesh cloth for reinforcement treatment at large gaps. If it is a prefabricated assembly joint or deformation joint, it is recommended to lay a layer of 200mm wide non-woven fabric strip or plastic film along the cracks, and then apply the product on the top and connect it with the surrounding coating. This can be effective. Extend the performance of this product to prevent the coating film from being cracked due to deformation of the base surface. 二ã€Polymer K11 waterproof paste Base surface treatment: 1. The base surface must be smooth, firm, clean, clear water, dust-free, and oil-free; 2. Obvious pores and cracks must be leveled with cement mortar; 3, leakage must first be plugging treatment, yin and yang angle should be made of arc angle. Preservation: Stored in a cool, dry place below 5°C, unopened, with a one-year retention period. Dosage: 1.8-3.0kg/m2 (theoretical coating amount) Packing: 20KG, 10KG, 5KG Instructions: 1. When smearing the bottom layer, pour the paint into the container, then mix it with a quarter of clear water and mix it, and then use it to improve the permeability of the paint to the base surface; 2, in the lower, middle, upper smear, paint directly stir, then use the standard brush, rubber scraper brushing on the base surface; 3, the coating thickness of 1.2-2mm (according to the requirements of the construction site for flexible control), uniform brushing 3-5 times, each time depending on the film curing and set, the general interval time is 6-24 hours. Application scope: Michol polymer K11 waterproof slurry is suitable for the waterproofing of roofs, basements, exterior walls, bathrooms, kitchens, and tunnels, bridges, ponds, reservoirs, grain stores, etc. of new and old buildings. Third, polymer K11 waterproof paste Mage Polymer K11 waterproof paste has good flexibility, can withstand slight vibration and displacement; non-toxic, odorless, and environmental protection; can be applied on the wet base surface; construction is quick and short in duration; water resistance, weather resistance, and durability Excellent corrosion resistance. Application scope: According to different waterproof design solutions; Type 1: The product is mainly used in non-long-term water-immersed building waterproofing projects such as roofing, exterior walls; Type 2: The product is suitable for building waterproofing projects under long-term flooding conditions such as: toilets, kitchens, basements, etc., and can be used for various old and new buildings and structures (eg underground works, tunnels, bridges, ponds, reservoirs, etc.). Precautions: 1. After the waterproof layer is completely dried, it can be used as a base coat; 2, can not be below 0 °C or rain construction, construction in a particularly humid and not ventilated environment will affect the film; 3, for special parts, nodes, according to the relevant provisions of the requirements of strengthening treatment, should add non-woven fabric or fiber network; 4. Do not use water after adding dry solid slurry. Storage: Stored in a cool, dry place above 5°C without unsealing. The shelf life is one year. Packing: 20kg drum Fourth, cement-based crystalline penetration waterproof slurry Meizhi Cement Based Permeable Crystalline Waterproof Slurry is made of U.S. imported additives and mixed with ordinary Portland cement as the base material to form a dew grey powder waterproof slurry, which can form a permanent and efficient waterproof overall with the concrete structure. Product Features: 1, there is a super penetration capacity and strong water pressure. 2, can increase the strength of concrete. 3, permanent waterproof and super self-repair ability. 4, resistant to chemical erosion. 5, good breathability and weather resistance, radiation resistance, UV resistance. 6, extensive application. 7, low construction cost, simple construction method, non-toxic, odorless, and environmental protection. Scope of application: Waterproof construction of concrete structure bases, construction of cracks, water seepage points, plugging of holes, construction of subway stations, underground continuous walls, tunnels, culverts, reservoir dams, waterproofing and plugging, industrial and civil basement, Waterproof construction on all bases of roofing, toilet and bath rooms, concrete building facilities, and all structural defects of concrete building facilities. Note: In the sub-zero degrees Celsius early strong waterproof slurry can be used instead of concentrated waterproof slurry construction, waterproof slurry in the freezing environment is best to use warm water deployment. The above about the k11 waterproof slurry is briefly introduced here, I hope to help you. For more information, please visit this website. Stay tuned. Windowsill waterproof basement waterproof bathroom waterproof specification tile waterproof sealant roof garden waterproof
3D Acrylic Edge Banding with Double Color Edge Banding and one color edge banding. Solid color and woodgrain design all be supported. Perfect transparent surface. Japan Acrylic raw material. German ink and JOWAT primer. Customize color and size for Acrylic edge banding. Sinowolf Plastic Dekor CO., LTD always focus on producing best quality edge band. Using high-end raw materials, all chemical additives import from Europe, to make sure our plastic edge banding keep stable quality 3-5 years. Our products range include PVC edge band, ABS edge band, 3D PMMA acrylic edge band, Aluminum edge band.
Unit Color 3D Acrylic Edge Banding China Unit Color Edge Banding, 3D Edge Banding, Unit Color Acrylic Edge Banding, Wood Unit Color Edge Banding Manufacturer, Unit Wood Color Edge Banding, 3D Acrylic Edge Banding Sinowolf Plastic Dekor Co., Ltd , http://www.sinowolfdekor.com
