Is it the first floor tile or the first wall tile ? In fact, the first wall tiles or floor tiles can be used. Which one is to be constructed first, the key is to pay attention to two issues: First, whether it is conducive to the protection of projects in the early construction; Second, whether it is conducive to a reasonable installation progress; If this problem is positive, then there is no problem whether it is the construction of a brick wall or the construction of a brick. If you are still bothered by paving the first floor or paving the wall , here's where I come to reveal the answer. First paving or paving first The former workers’ masters were first paving slabs, but first paving the floor tiles, at least for a period of time after the paving slabs were laid, you were idle. You cannot step on the bricks. You cannot ask the workers to spread the wall tiles. When you step on the floor, the tiles are not even. In addition, when the tiles are first affixed, there will be cement and sand falling on the tiles when the wall tiles are attached. The hardness of the sand is large, and the surface of the tiles will be scratched during construction. In addition, it is not easy to be sanitary; after the tiles are attached, the floor drain is opened. The slurry flow easily into the ground. Cement can be solidified by being soaked in water, and blocking the pipes is troublesome. It is now common to shop walls first, starting from the middle and setting aside the height of a brick. When laying, put a brick underneath to prevent the above bricks from sliding down. Wait until the bricks are completely glued and you can remove them. Special circumstances: Some people are not horizontally vertical houses, and there is a point of error because there is a claw line, for fear of the first shop wall tiles, walls and floor tiles will have gaps in error, not on, affect the appearance. The gap between the tiles is not a big problem. Workers will do pre-paving before paving. If they can be found after the shop is finished, they will not be able to stay on the edge and will not affect the appearance. The general is in the corner, and it is not obvious. Wall tiles and floor tiles steps [Step 1] A horizontal line is measured at any elevation around the wall to start attaching the wall tile, but the order of the wall tiles must be controlled so as to avoid the number of times of multiple cutting. It can both improve efficiency and does not hinder beauty. [Step 2] After sticking the wall tiles, the Jinsheng Tiles will be laid to control the slope of the drainage. Note that the sanitary napkins should not be allowed to flow backwards (flow toward the doorway) and the protection should be protected. After closing, the water shutoff experiment should be conducted to ensure no leakage. [Step 3] Cleaning, steel balls can be used for wall cleaning. Wall tiles and floor tiles considerations Note one: Before the tiling should clean up the grass, such as lime plaster, latex paint, wallpaper and other decorative materials on the wall, or dirt on the ground, be sure to clean, otherwise the cement mortar and the grassroots adhesion is not strong; If the wall itself has cracks, it should be properly treated before it can be tiled, so as to avoid future basic structural cracks caused by cracking or falling off the wall tiles; also, for the flatness or verticality gap is too large for the floor, wall, Also use cement mortar for leveling treatment. Note two: paste the floor tile should be posted from the inside, such as the ground slope or leak, should pay attention to the direction of the drainage slope; wall tiles should be laid from the bottom, for the sake of beauty, the bottom of the brick should be posted. After pressing the tiles, press the floor tiles. When there are half bricks, you should try to place them below. In addition, a wall cannot be attached to the top at a time to prevent the tile from being heavy and causing it to fall. Note 3: Wall tiles have a high moisture content, which must be taken into consideration when pasting. The tile base should be fully moistened before it is tiled, and ceramic tiles should also be soaked in water for at least 20 minutes before use. Otherwise, the moisture in the mortar is rapidly absorbed by the dried substrate and tiles and condenses quickly, which affects the fastness of the bond. Wall tiles will also absorb moisture from the cement so that the cement does not function as an adhesive. In addition, the water absorption rate of each type of wall tile is not the same, which depends on the experience to grasp. Editor's summary: The above is the decoration knowledge Q&A: The first paving tile or the first paving tile different areas paved with stress-related presentations, hoping to help meet the needs of the friends! For more information, please continue to follow our website, follow-up will show more exciting content. You can also purchase more of your favorite products on Qijia Mall! Bathroom wall tile balcony exterior wall brick wall background wall living room wall brick wall tile price
Kemtron Shaker Screen models: Kemtron KTL48 shaker screen, Kemtron KPT28 Shaker screen,
Kemtron Shaker Screen types is a kind of steel frame shaker screen
Steel frame shaker screen main feature as follows:
Kemtron Shaker Screen Kemtron Shaker Screen,Kemtron Oil Shale Shaker Screen,Kemtron Shale Shaker Screen,Shaker Screens For Sale Anping Shengjia Hardware Mesh Co.,ltd , https://www.oilshakerscreen.com
